Announcement

Collapse
No announcement yet.

davit pictures

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • AkBillyBow
    replied
    Nice job. Looks great!!

    Leave a comment:


  • rmk4x4
    replied
    built it with spring loaded pin to hold the davit were i wanted it.
    Attached Files

    Leave a comment:


  • rmk4x4
    replied
    got our davit done last week and the honda moter and capstan put togeather turned out pretty nice is made from sch80 tube with 1/4 gusseting
    Attached Files

    Leave a comment:


  • AkBillyBow
    replied
    I also have the Honda gas puller on a davit. I bought mine together, and would build it taller if I were to start over. I installed another tube that my davit sits in, where I can spin it in towards the boat (as in this picture) for traveling, or out over the water (about 90 degrees from picture position) when in use. I also made it so I can lift it up another 1 1/2 feet taller (inside the outer tube) and pin it. I drilled 2 holes through both the davit and outside tube and bolt it in each position, so it won't move om me. Hopefully I did not confuse you on this!!

    AkBillyBow
    Attached Files

    Leave a comment:


  • rmk4x4
    replied
    thanks for the pics they help out alot will post some pics of the whole setup when i am done just waiting on the parts now

    Leave a comment:


  • potbuilder
    replied
    You'll want your line coming onto the head at less of a angle than this but you get what i mean, top and left would be coming from the block on the davit
    Click image for larger version

Name:	P4080286.jpg
Views:	1
Size:	40.3 KB
ID:	2479098

    If it comes on at a angle like this your sure to have a mess on your hands
    Click image for larger version

Name:	P4080287.jpg
Views:	1
Size:	43.4 KB
ID:	2479099

    Leave a comment:


  • rmk4x4
    replied
    Originally posted by potbuilder View Post
    OK now i know who you are!! We talked about the hauler when they were here. Make sure the line leads into the head at a slight angle and tape down any nubs or ends sticking out of the rope at knots or splices. A couple of kill switches to the motor would be good to have in different locations.

    so you want your pully on the davit to have a slight angle to the out side of the head is that right? i was thinking about a teather kill on the moter seems like it would be good thing. we went with the honda cause putting it togeather ourselves was cheaper than anthing you could buy local even after shipping. on the davit i am thinking about 1 1/2 sch 40 pipe with a flat bar gussed the whole length of the davit i have the part to the boat figured out to be rock soild so dont want to worry about the davit as i am told the gas haulers will really pull. any advice i am all ears thanks Trevor

    Leave a comment:


  • potbuilder
    replied
    Originally posted by rmk4x4 View Post
    my mom and dad bought some gear from you a few days ago thanks for getting them setup as we are new to shrimping. Will be carfull not to loose any fingers.
    OK now i know who you are!! We talked about the hauler when they were here. Make sure the line leads into the head at a slight angle and tape down any nubs or ends sticking out of the rope at knots or splices. A couple of kill switches to the motor would be good to have in different locations.

    Leave a comment:


  • rmk4x4
    replied
    Originally posted by potbuilder View Post
    All i'm going to say is watch out for riding turns on that capstan, they'll grab ya and hurt ya in a blink.
    my mom and dad bought some gear from you a few days ago thanks for getting them setup as we are new to shrimping. Will be carfull not to loose any fingers.

    Leave a comment:


  • potbuilder
    replied
    Originally posted by rmk4x4 View Post
    i am going to be building a davit for out boat soon and want to see some pics of what others have done. it will be going on a bayliner 2556 and i will be using a honda powered puller buying the moter and capstan and building it myself
    All i'm going to say is watch out for riding turns on that capstan, they'll grab ya and hurt ya in a blink.

    Leave a comment:


  • rmk4x4
    started a topic davit pictures

    davit pictures

    i am going to be building a davit for out boat soon and want to see some pics of what others have done. it will be going on a bayliner 2556 and i will be using a honda powered puller buying the moter and capstan and building it myself

Footer Adsense

Collapse
Working...
X