I am putting in a small bilge pump in my 20' flatbottom river boat. Currently there is no electronic stuff on the boat other than starting. ...
I dont know what im talking about about just curios. I have A 25 wooldridge classic. What happens if you weld say a foot long or so hull extion the...
Removed post
has any one out there switched to boyesen reeds on ther outboard? are they all they say they are. how much more fule savings did you get out of them?...
i was wonderin if any one has done this and has any pointers i have a 20ft. monark i was thinking or putting my hopped up v6 stock car motor in it...
I plan on building a 18 foot Don Hill Fly Fisherman. I am not sure what wood I am using but i plan on glassing the entire boat. if anyone has built a...
Anyone convert their 350 to a 383? Did you gain enough hp and torque to make it worth the extra parts and machining?
I have a short shaft motor I want to put on a skiff on a lake It's a 16' x 64" with a 21" transom, I think it's a starcraft but the data plate...
I just bought a 1998 Harbercraft Landing Craft center console. The boat has had a hard life, but it isn't really banged up too bad. Like most...
Tried this in the boating section, but no luck so here goes: Curious about you guys' opinions on high thrust vs. standard 50 4 stroke motors;...
My Yamaha 1652 G3 with a F60 Jet never could get up on step very well. Dewey's installs the outboard with a motor jack that pushes the outboard out...
Is there anyone in AK that makes them? I have a 95 hewes river runner and I want one for when I go salt fishing. I found a few online but shipping...
This thread is the outcome of a conversation among a group of boaters discussing the pro's and con's of UHMW and its increasing popularity as boaters...
A week ago my wife & I pulled the old jetboat(my father & I used to take it out a couple times a year in the early 90s until I disappeared to the...
I've got a 20'wooly sport and the 2 front seats a mounted on storage boxes with swivels. I've seen some of the "big" suspension seats that are...
Well learned a lesson, read manual and it will tell ya there is a grease zert on the top of the bellhousing that lubes the center bearing which...
Anybody have experience with these I just bout some trim tabs by nauticus for my 1852 alweld with a 70/50 jet. I noticed in the instructions they...
Looking to finish a small jet boat floor w/ aluminum diamond plate. Have enough for up at the bow, but need an approx 4'x5' to 4'x6' sheet for the...
I'm considering changing out the foam in my engine compartment, hood, maybe even going further and attacking the rear of my boat to quiet things down...
Got a quote for a canopy, height 5'10" 95" beam and appox 9' long. It's would be made of 100% water proof fabric, I'm told it's the best you can get,...
I know this area doesn't get a lot of traffic but oh well. I have a 1986 Bayliner Trophy and I'm doing some minor mods to the boat. I'm a DIY kinda...
looking to power a 20' woolridge with 150-175 hp jet outboard,any advice will be greatly appreciated.
so I am looking at a seaark 1652 tunnel that needs a transom raise in order to accomodate the 25 inch outboard that will someday sit on it. does...
what do U know about changing HP by changing PC board.
http://forums.iboats.com/showthread.php?p=2360521#post2360521 Up to 1993 it said, I did the PDF and saved & printed one for my AQ125A for free. ...
I want to mount some plastic bases/swivel seats (with qwik releases) in an aluminum skiff with aluminum bench seats (underfilled with floatation) so...
Both of my Exhaust Manifolds are cracked almost in half, guess the guy who winterizes got me. What I would like help with is what will fit and hope...
Ok, i bit the bullet on a new boat. I am looking for somewhere that sells a live well for the 1875 xs, Or some where that can have one specially...
Blew a fuse and couldn't see which one it was yet I knew what it went to. So I started to write down which was which, so then being bored thought I'd...
Who in Alaska sales marine plywood? Do you have to do anything with it? Like seal it? With what? Thanks Bob
There are currently 1 users browsing this forum. (0 members & 1 guests)
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
